ABB TTF200 Operating	 Instruction Download Page 4

TTF200

 FIELD-MOUNT TEMPERATURE TRANSMITTER  |  OI/TTF200-EN REV. A 

 

 

 

 

1

 

Safety 

 

1.1

 

General information and instructions 

These instructions are an important part of the product and 
must be retained for future reference. 
Installation, commissioning, and maintenance of the 
product may only be performed by trained specialist 
personnel who have been authorized by the plant operator 
accordingly. The specialist personnel must have read and 
understood the manual and must comply with its 
instructions. 
For additional information or if specific problems occur that 
are not discussed in these instructions, contact the 
manufacturer. 
The content of these instructions is neither part of nor an 
amendment to any previous or existing agreement, promise 
or legal relationship. 
Modifications and repairs to the product may only be 
performed if expressly permitted by these instructions. 
Information and symbols on the product must be observed. 
These may not be removed and must be fully legible at all 
times. 
The operating company must strictly observe the applicable 
national regulations relating to the installation, function 
testing, repair and maintenance of electrical products. 
 

1.2

 

Warnings 

The warnings in these instructions are structured as follows: 
 

DANGER 

The signal word "DANGER" indicates an imminent danger. 
Failure to observe this information will result in death or 
severe injury. 

 

WARNING 

The signal word "WARNING" indicates an imminent danger. 
Failure to observe this information may result in death or 
severe injury. 

 

CAUTION 

The signal word "CAUTION" indicates an imminent danger. 
Failure to observe this information may result in minor or 
moderate injury. 

 

NOTICE 

The signal word "NOTICE" indicates useful or important 
information about the product. 
The signal word "NOTICE" is not a signal word indicating a 
danger to personnel. The signal word "NOTICE" can also 
refer to material damage. 

 

 

 

1.3

 

Intended use 

This device is intended for the following uses: 
—  To measure the temperature of fluid, pulpy or pasty 

substances and gases or resistance/voltage values. 

The device has been designed for use exclusively within the 
values stated on the name plate and within the technical 
limit values specified on the data sheets. 
—  The maximum and minimum operating temperature 

limits must not be exceeded or undershot. 

—  The permissible ambient temperature must not be 

exceeded. 

—  The housing's IP rating must be observed during 

operation. 

 

1.4

 

Improper use 

The following are considered to be instances of improper 
use of the device: 
—  For use as a climbing aid, e.g. for mounting purposes. 
—  For use as a support for external loads, e.g. as a support 

for piping, etc. 

—  Material application, e.g. by painting over the name 

plate or welding/soldering on parts. 

—  Material removal, e.g. by spot drilling the housing. 
 

Summary of Contents for TTF200





































Reviews: