ABB TPL65VA32 Operation Manual Download

Page: 35 / 124

Operation Manual / TPL65VA32/33

Commissioning

Oil supply

3.1

Page 33

ber

2016

L2464_

ion

Commissioning

Oil supply

3.1

A carefully designed and installed oil supply, which functions in all possi-

ble operational conditions, is an important prerequisite for trouble-free tur-

bocharger operation.

The turbocharger is normally lubricated with oil from the engine oil circuit.

NOTICE

With regard to the oil supply, please observe the engine builder's speci-

fications for lubricating oil selection, oil change intervals, oil filtration, oil

pressure and oil temperature.

Oil filtration

A lubricating oil filter system with a filter mesh size of

≤ 0.034 mm is ade-

quate for this turbocharger.

3.1

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands