ABB TPL65VA32 Operation Manual Download

Page: 32 / 124

Operation Manual / TPL65VA32/33

Safety

2.8

Page 30

ber

2016

L2464

_EN

ion

Hazards due to electrical components

WARNING

Hazards due to electrical components
Electrical components operate with voltages which can present hazards

to humans.



All work on or with electrical components may only be performed by

trained specialists.



Heed any country-specific regulations.

Periodic checking of the pressure vessel

2.8

The pressure vessels used by ABB Turbo Systems, such as those for wet

or dry cleaning, are so-called "simple pressure vessels".



The local, statutory regulations covering periodic checks of pressure

vessels must be observed.



The operator is responsible for the safe operation of the pressure ves-

sel.

WARNING

Hazards from pressure vessels
The operator must keep the pressure vessel in a proper condition and

monitor it. Necessary repair or maintenance work must be carried out

without delay and the required safety precautions must be taken.



Pressure equipment must not be operated if it has defects.

2.8

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands