background image

 

 

 

 

2TLC172139M0201, rev. B 

www.abb.com/ljokabsafety 

2013-03-02 

2  Overview 

General description 

ABB/Jokab Safety adaptor units are used to adapt conventional safety sensors where the safety relies on e.g. one- 

or two-channel static signals, OSSD outputs, or short circuit detection, to the dynamic safety circuit monitored by a 

Vital safety module or Pluto safety-PLC.  
Tina 7A is used to adapt safety sensors with mechanical contacts to the dynamic safety circuit. Examples of such 

safety sensors are emergency stops and switches or light curtains and light beams with internal relay outputs. The 

unit is also able to monitor short circuits and can therefore also adapt safety sensors with safety contact rails, or 

safety mats with internal relay outputs, to the dynamic safety circuit. 
Tina 7A is intended for use inside electrical cabinets where it can be mounted on 35 mm DIN rails and connection 
cables can be connected directly to screw terminal blocks on the unit. Tina 7A is also equipped with a LED for 

visual status information of the safety sensor and the dynamic safety circuit. 
The Tina 7A adaptor unit is intended for use in safety circuits in accordance with EN 60204-1. 

 

Warning! 

In order to maintain the highest safety level and reduce the risk of electrical interference the unit must be 

installed within the same physical encapsulation as the safety device. The connection cables should be as short as 

possible (max 150 mm). 

Safety regulations 

 

Warning!

 

Carefully read through this entire manual before using the device. 
The devices shall be installed by a trained electrician following the Safety regulations, standards and the Machine 

directive.  
Failure to comply with instructions, operation that is not in accordance with the use prescribed in these instructions, 

improper installation or handling of the device can affect the safety of people and the plant. 
For installation and prescribed use of the product, the special notes in the instructions must be carefully observed 
and the technical standards relevant to the application must be considered. 
In case of failure to comply with the instructions or standards, especially when tampering with and/or modifying the 

product, any liability is excluded. 

 

 

Summary of Contents for Tina 7A













Reviews: