background image

 

 

2TLC172121M0201, rev. A 

10 

www.abb.com/lowvoltage 

2011-09-20  

6  Technical data 

Manufacturer 

Address 

ABB AB / JOKAB SAFETY 
Varlabergsvägen 11 
SE-434 39 Kungsbacka 
Sweden 

Article number/Ordering data 

Tina 2A: 2TLA020054R0100 
Tina 2B: 2TLA020054R1100 

 

Power supply 

Operating voltage 

24 VDC +15 %, -25 % 

Total current consumption 

17 mA (27 mA with max information output) 
Information output: Max 10 mA 

Time delay t (in/out) 

t < 60 µs 

Voltage supply at normal operation (protection 
OK) and 24 VDC supply voltage 

Dynamic input: between 9 and 13 volt (RMS) 
Dynamic output: between 9 and 13 volt (RMS) 
Information output: ~ 23 VDC 

 

General 

Protection class 

IP67 

Ambient temperature 

Storage: -30…+70°C 
Operation: -10…+55°C 

Humidity range 

35 to 85 % (with no icing or condensation) 

Housing material 

PVC 

Connector 

5x 0.34 mm

2

 wires, 0.15 m 

Size 

Tina 2A: 46 x 27 x 24 mm  
Tina 2B: 26 x 21 x 7 mm (L x W x H) 

Weight 

Tina 2A: ~30 g  
Tina 2B: ~20 g 

Colour 

Black 

 

Safety / Harmonized Standards 

Conformity 

European Machinery Directive 2006/42/EC 

 

EN ISO 12100-1:2003, EN ISO 12100-2:2003, 
EN 60204-1:2007, EN 954-1:1996, EN ISO 13849-1:2008, 
EN 62061:2005 

IEC/EN 61508-1…7 

SIL3, PFHd: 4.50*10

-9

 

EN 62061 

SIL3 

EN ISO 13849-1 

Performance level: Pl e, category 4 

EN 954-1 

Category 4 

Certificates 

TÜV Nord 

Summary of Contents for Tina 2B













Reviews: