background image

 

TERRA DC WALLBOX 

 
 
 

2022-11-15 

 

9/20 

 
 
 

2.2.

 

MID certified Charger identification  

 

The nameplate contains all information relating to the Deutsche Messe EV regulation for the 
measuring device calibration law. This is a field-installable upgrade. To recognize if a charger is 
compliance to MID Directive, Check the charger label. The product compliance is indicated by the 
info showed in the Highlighted box 

The Label reports all the necessary info to be compliance to 2014/32/EU MID directive. 

2.3.

 

Energy Meter Readout: 

A. Time (hh:mm:ss) 

B. Date (YY-MM-DD) 

C. Delivered DC power (kWh)  

 

 

Charger registration to the Federal authority:  

o

 

https://www.bundesnetzagentur.de/DE/Sachgebiete/ElektrizitaetundGas/Unternehm

en_Institutionen/HandelundVertrieb/Ladesaeulen/Anzeige_Ladepunkte_node.html 

 

Section 31-33 MessEG :  

o

 

MessEG is published on: 

https://www.gesetze-im-internet.de/messeg/index.html 

                         (directly to standar

link

) 

 
2.4.

 

Charger configurations 

Terra DC Wallbox Charger supports the following DC charging standards: 

Indicator 

Description 

CJ 

One CCS and one CHAdeMO outlets up to 60 A / 22.5 kW; 
No simultaneous charging possible 

One CCS outlet with output current/power; 60 A / 22,5 kW 

One CHAdeMO outlet with output current/power; 60 A / 22,5 kW 

Summary of Contents for Terra DC wallbox





















Reviews: