ABB Terra 94 Installation Manual Download Page 5 | Manualshive

Page: 5 / 54

ABB Terra 94 Installation Manual Download Page 5

7

Troubleshooting................................................................................ 37

Troubleshooting procedure...................................................................................................37

8

Technical data....................................................................................38

EVSE type.................................................................................................................................. 38

Parts included in the delivery................................................................................................ 38

General specifications............................................................................................................39

Required tools for installation.............................................................................................. 39

Torque specifications............................................................................................................ 40

Ambient conditions................................................................................................................ 40

Mass and center of gravity....................................................................................................40

Noise level.................................................................................................................................40

Transport specifications........................................................................................................41

Dimensions............................................................................................................................... 41
8.10.1

General dimensions................................................................................................ 41

8.10.2  Cable slack................................................................................................................ 41
8.10.3  Floor space requirements..................................................................................... 42
8.10.4  Prefab foundation...................................................................................................43
8.10.5  Custom foundation................................................................................................44

Logic interface specifications.............................................................................................. 44

AC input specifications.......................................................................................................... 45
8.12.1

General AC input specifications...........................................................................45

AC input cable..........................................................................................................45

Terra 94.....................................................................................................................45

Terra 124................................................................................................................... 46

Terra 184...................................................................................................................46

DC output specifications.......................................................................................................46
8.13.1

General specifications........................................................................................... 46

Terra 94.....................................................................................................................46

Terra 124................................................................................................................... 48

Terra 184...................................................................................................................50

Power consumption................................................................................................................ 51
8.14.1

General specifications............................................................................................51

Terra 94..................................................................................................................... 51

Terra 124....................................................................................................................51

8.14.4 Terra 184................................................................................................................... 52

Current peaks during the start of a charge cycle..............................................................52

Contents

BCM.S1102.0-EN | 001

5

«
...
3
4
5
6
7
...
»

Summary of Contents for Terra 94























































Reviews:

No comments