ABB SACE Emax 2 E4.2 Instruction Handbook Manual Download Page 63

Page: 63 / 72

Disassembly instruction emaX 2 e4.2

6.14 PHASE 14 – POLES

Actions to be performed

Tools

No. 10

No. 25

Torx key

Allen key

230

By means of the allen key unscrew the 2 screws

fixing the sensor cover to the pole.

233

By means of the flat screwdriver remove the

cables cover and after manually remove the

wire.

235

Manually remove the sensor.

232

By means of the torx key (size 10) unscrew the

screw fixing the wire to the pole.

234

By means of the flat screwdriver unhook the

sensor plug mounted below the sensor and

after manually remove the sensor plug.

231

Manually remove the sensor cover.

4mm

Flat screwdriver

Hammer

Cross screwdriver

Rod Ø5mm

Min. 200mm

Summary of Contents for SACE Emax 2 E4.2









































































Search results

Summary of Contents for SACE Emax 2 E4.2

Reviews:

Related manuals for SACE Emax 2 E4.2

Brands by name

Popular brands

ABB SACE Emax 2 E4.2, Instruction Handbook Manual

Search results

Summary of Contents for SACE Emax 2 E4.2

Reviews:

Related manuals for SACE Emax 2 E4.2

Brands by name

Popular brands