ABB RTU560 Operation Manual Download Page 7

RTU560

 

Connections and Settings  
Communication Unit 560CMD11 

 

Doc.-No.: 1KGT 150 765 V005 1 

 

 

Settings 

Hardware settings and operation of the communi-
cation Interfaces of the 560CMD11 are carried out 
with the RTUtil560 configuration tool. For the con-
figuration  procedure  of  the  communication  Inter-
faces  and  the  IO-Bus,  please  refer  to  the 
560RTUtil user guide. 

The  following  parameters  have  to  be  defined  for 
all protocols: 

 

Baudrate: 

 50  to 19 200 baud Mo-

dem control: 

 

Direct link (TxD/RxD only) 

 

WT  link  full  duplex  (560FSM10/11  no 
handshake)  

 

WT  link  half  duplex  (560FSM10/11  with 
RTS / DCD) 

 

Dial  up  (external  modem  without  hand-
shake, without RTS / CTS) 

 

Loop  switch  unit  (RP570/71  Host  Inter-
face only) 

 

Link  with  collision  avoidance  (TxD,  RxD, 
DCD, without handshake (DNP 3.0 only) 

 

The settings of the Ethernet Interface are: 

 

Node name 

 

IP address 

 

Subnet mask 

 

Default gateway 

 

Routing information 

 

The number of the host Interface. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 6: 560ANA02 

 

 

For  the  configuration  procedure  of  the  GPRS-
Modem (only R0011),  please refer to the  function 
description part 6. 

The settings of the GPRS-Modem are: 

 

Local IP address 

 

Remote network IP address 

 

PIN number SIM-Card 

 

Username 

 

User password 

 

Provider Connectionstring (APN) 

 

RF sensitivity (only R0011) 

 

Main  parameters  for  the  transmitter 
are:  

  Max. output power: 30dBm ± 5dB  

  Min. output power:  0dBm ±5dB  

 

min.  signal  level  at  input  of  GPRS-
Chip: -108dBm 

 

cable  RG58  with  losses  of  0,546dB/m 

 10,92dB (20m) 

 

antenna with a gain of 2,2dBi 

 

Exemplary calculation: 

min. signal (receive) with 20m cable = 
-109dB + 10,92dB 

– 2,2dBr =  

-99,28dBm 

result:  the  RF  signal  at  the  point  of 
antenna shall be min. -99,28dBm 

Summary of Contents for RTU560











Reviews: