manualshive.com logo in svg

ABB RTU560, Operation Manual, Page: 6 / 10

Share
Download
ABB RTU560 Operation Manual Download Page 6

RTU560 

Connections and Settings  
Communication Unit 560CMD11 

 

Doc.-No.: 1KGT 150 765 V005 1 

 

6 

 

Firmware Version 

The  current  firmware  version  will  be  delivered  on 
a  CompactFlash  memory  card.  A  new  firmware 
file can be loaded via the Web diagnostic tool into 
the removable CompactFlash

 

memory card. 

For changing the CompactFlash

 

memory card the 

right  side  of  the  housing  has  to  be  opened  (see 
Fig. 8 and Fig. 11).  

!!

 

 

1.  Disconnect  the  power-supply  of  the 

560CMD11. 

2.  Take  care  of  ESD  protection  before 

opening the 560CMD11 housing. 

3.  Open the 4 screws on the right side of 

the housing (see Fig. 8 and Fig. 11). 

4.  Pull  or  plug  only  the  CF-card. 

Don’t 

touch other components. 

5.  Close  the  housing  before  the  power- 

supply is connected to the 560CMD11 

 

 
SIM-Card (only R0011) 

For communication  via the GSM/GPRS modem a 
pluggable SIM-Card (ID-000) is necessary. 

For  changing  the  SIM-Card  the  right  side  of  the 
housing has to be opened (see Fig. 11).  

!!

 

 

1.  Disconnect  the  power-supply  of  the 

560CMD11. 

2.  Take  care  of  ESD  protection  before 

opening the 560CMD11 housing. 

3.  Open the 4 screws on the right side of 

the housing (see Fig. 11). 

4.  Pull  or  plug  only  the  SIM-Card. 

Don’t 

touch other components. 

5.  Close  the  housing  before  the  power- 

supply is connected to the 560CMD11 

 

For changing the CF - card 
follow the instructions below

: 

For changing the SIM-Card 
follow the instructions below

: 

Summary of Contents for RTU560











Reviews:

No comments