ABB ICOS GLA431-MCIA User Manual Download Page 35

Page: 35 / 111

USER MANUAL

| ICOS | INSTRUCTIONS | UM/ICOS-EN REV. B.2

Table 7 describes fault criteria for the Temperature Alarms.

Table 7: Fault Criteria for Temperature Alarms

Status

Sensor Read

Fault Condition

Description

Analyzer Temp

Temperature High/Low

Alarm

The temperature exceeds the operating
temperature range.

CROSS OVER

Analyzer Temp

Temperature High/Low

Warning

The temperature is > the high warning
set point.

The temperature is < the low warning
set point.

Fault

NaN reading

Occurs when there is a false or
undefined value. (NaN= not a number)

Dead Band

Acceptable

Range

No warning/alarm

If the

Alarm Status

is Yellow or

Red,

please refer to the

Maintenance

section on

page 60. If issue continues, please contact [email protected]

Summary of Contents for ICOS GLA431-MCIA
















































































































Search results

Summary of Contents for ICOS GLA431-MCIA

Reviews:

Brands by name

Popular brands

ABB ICOS GLA431-MCIA, User Manual

Search results

Summary of Contents for ICOS GLA431-MCIA

Reviews:

Brands by name

Popular brands