ABB i-bus VC/S 4 1 Series Product Manual Download Page 142

Page: 142 / 199

ABB i-bus® KNX

PARAMETERS

7.4.151

Valve drive operating principle, de-energized

This parameter is used to define the operating principle of the valve drive connected.

Option

Closed

The valve is closed if no current flows through the valve drive. The valve is opened if current flows
through the valve drive.

Open

The valve is opened if no current flows through the valve drive. The valve is closed if current flows
through the valve drive.

Prerequisites for visibility

\ Parameter

\ Options

Thermoelectric (PWM)

Open/close signal

• The parameter is in the parameter window

Channel X

\ parameter window

Valve output X

7.4.152

I-bus® Tool access

This parameter is used to define whether the device can be accessed via the i-bus® Tool.

More information: → ⁠

Integration into i-bus® Tool, Page ⁠⁠27

Option

Deactivated

Access via the i-bus® Tool is deactivated.

Value display only

Values can be displayed via the i‑bus® Tool.

Full access

Values can be displayed and changed i‑bus® Tool.

Prerequisites for visibility

• The parameter is in the parameter window

Basic settings

7.4.153

Reset manual setpoint adjustment when base setpoint received

Note

This parameter only has an effect if the option

Relative

is set in the parameter

Setpoint specification

and adjustment

This parameter is used to define whether manual setpoint adjustment is reset when a new value is re-
ceived on group object

Basic setpoint

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

142

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Summary of Contents for i-bus VC/S 4 1 Series








































































































































































































Search results

Summary of Contents for i-bus VC/S 4 1 Series

Reviews:

ABB i-bus VC/S 4 1 Series, Product Manual, Page: 142 / 199

Search results

Summary of Contents for i-bus VC/S 4 1 Series

Reviews: