ABB HT611658 Operation Manual Download

Page: 84 / 148

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.5 Removing the compressor casing

HZTL4033_EN

Rev.K

January 2022

9.5

Removing the compressor casing

Removing wall insert

Fig. 37: Removing wall insert

1. Loosen screws (72011) and remove with washers (72008).

2. To secure the wall insert, screw in one screw (72011) a third of the way.

3. Press off wall insert with three screws (72011) until the lifting device (90190) and the fix-

ing segment (90192) can be fitted.

4. Fit the lifting device (90190) and the fixing segment (90192) to the flange of the wall in-

sert (77000) using the screws (90197) and washers (90198).
Depending on the hole pattern of the wall insert (77000), the screws (90197) cannot be
fitted symmetrically.

5. Put on shackle (90195) and fasten to lifting gear.

6. Remove locking screw (72011).

Page

146

Summary of Contents for HT611658



















































































































































Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands

ABB HT611658, Operation Manual

Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands