ABB HT611658 Operation Manual Download

Page: 58 / 148

Operation Manual / A170-M.. - A175-M..

7 Periodic maintenance / 7.2 Cleaning the filter silencer

HZTL4033_EN

Rev.K

January 2022

CAUTION

Penetration of dirt and foreign particles

Any penetration of dirt and foreign particles into the compressor can dam-
age it.

Fit the connecting rods (81269) correctly in the slots on the filter silencer
body (81135).

It must not be possible to rotate or move the cover grid (81266) after as-
sembly.

Check the position and alignment of the connecting rods during and after
assembly.

Fig. 27: Cleaning the filter silencer (2)

Place cover grids (81266) evenly and in the correct position.

Push connecting rods (81269) through the lugs of the cover grids (81266).

Connect the connecting rods (81269) with the screws (81272). When tightening the
screws (81272), make sure that the flattened ends of the connecting rods (81269) are cor-
rectly positioned on the edge of the filter silencer body (81135).

Tighten screws (81272) alternately and evenly. Observe tightening torque

Screw

Tightening torque [Nm]

81272

Table 15: Tightening torque (81272)

Fit the lock nuts (81273) on the screw (81272). Observe tightening torque.

Lock nut

Tightening torque [Nm]

81273

Table 16: Tightening torque (81273)

If present: Fit the filter ring (81265)

Cleaning the filter silencer

→

Page

146

Summary of Contents for HT611658



















































































































































Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands

ABB HT611658, Operation Manual

Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands