ABB HT578566 Operation Manual Download | Manualshive

Page: 85 / 122

background image

Operation Manual / 4 Product description / A130-H.. - A140-H

7 Eliminating malfunctions / 7.5 Speed measurement system

© Copyright 2017 ABB. All rights reserved.

HZTL4030_EN

Revision D

May 2017

7.5

Speed measurement system

No signal or poor signal amplitude of the speed measurement

Possible causes

Remedy

Turbochar-
ger

The speed sensor was acci-
dentally fitted with an addi-
tional gasket.
An enlarged distance
between the sensor tip and
the signal-emitting sealing
disc reduces the voltage
amplitude of the speed sig-
nal.

The screw plug for the sensor is fitted with an
additional gasket (copper ring).
For information regarding the disassembly and
assembly of the speed sensor, refer to chapter

Replacing the speed sensor

.

Install the speed sensor without the additional
gasket (copper ring).

Sensor or cable defective

Contact an ABB Turbocharging Service Station.
Order new speed sensor (86505) (refer to
chapter

Ordering spare parts

).

Replacing the speed sensor

.

Table 26: Malfunction of the speed measurement system – No signal or poor signal amplitude

Measured speed too high

Possible causes

Remedy

Turbochar-
ger

Sensor tip contaminated,
since it is magnetic and can
attract metallic particles.
This reduces the distance to
the signal-emitting sealing
disc, which can lead to amp-
lification of the noise com-
ponent and, hence, to false
triggering.

For information regarding the disassembly and
assembly of the speed sensor, refer to chapter

Replacing the speed sensor

.

Dismantle the sensor, clean the sensor tip, and
fit the sensor back on with the specified tighten-
ing torque.

Table 27: Malfunction of the speed measurement system – Measured speed too high

Measured speed too low

Possible causes

Remedy

Turbochar-
ger

- -

Contact ABB Turbocharging Service Station

Table 28: Malfunction of the speed measurement system – Measured speed too low

If none of the measures described above remedy the malfunction, have the speed measure-
ment system checked by an ABB Turbocharging Service Station.

Page

55

/

91

«
...
83
84
85
86
87
...
»

Summary of Contents for HT578566



























































































































Reviews:

No comments

Related manuals for HT578566

Brand: SUEX Pages: 40

Brand: Vante Pages: 12

Brand: i-tec Pages: 32

Brand: SUHNER ABRASIVE Pages: 56

Brand: 360 electrical Pages: 2

Multi-Battery Charger

Brand: Cognex Pages: 2

Brand: Milwaukee Pages: 19

Brand: Laser Pages: 2

Brand: Vanner Pages: 12

Brand: i.safe MOBILE Pages: 100

Pathfinder Ultra Silver 6032

Brand: Monarch Pages: 13

Brand: Targus Pages: 26

Brand: Bahco Pages: 126

Brand: Shure Pages: 14

PowerScan 7000BT

Brand: Datalogic Pages: 2

Brand: BlackVue Pages: 28

Brand: Competition Electronics Pages: 2

Brand: CEN-TECH Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands