ABB HT578566 Operation Manual Download

Page: 117 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

12 Spare parts / 12.1 Ordering spare parts

HZTL4030_EN

Revision D

May 2017

Spare parts

12.1

Ordering spare parts

CAUTION

Spare part storage

All spare parts that were ordered together with the turbocharger must be
kept intact and ready for use.

Carefully clean any rusted parts and grease them.

Please quote the following data when making queries and ordering spare parts:

Turbocharger type

Serial number of the turbocharger

Designation and part number

Spare parts can be ordered from any ABB Turbocharging Service Station.

If different model variants are not taken into account in this document, contact an ABB
Turbocharging Service Station.

Dispose of placed and unusable parts in an environmentally-friendly and professional
manner in accordance with the local regulations.

Dispose of the packaging of new parts in an environmentally-friendly and professional
manner in accordance with the local regulations.

12.2

Required customer spare part set (97070)

For the operations described in the Operation Manual, the customer spare part set (97070)
is required. These parts are only available in the complete set.

Part number

Designation

Quantity

42012

O-ring (high-temperature resisting, colour: red or green)

61002 *

Gasket

77005

O-ring

79041

Counter-sunk screw

81010/ 82010

O-ring

Table 44: Customer spare part set 97070

* This gasket can only be installed when a gas outlet casing from ABB Turbo Systems is used.

Page

Summary of Contents for HT578566



























































































































Search results

Summary of Contents for HT578566

Reviews:

Related manuals for HT578566

Brands by name

Popular brands

ABB HT578566, Operation Manual

Search results

Summary of Contents for HT578566

Reviews:

Related manuals for HT578566

Brands by name

Popular brands