ABB HT576936 Operation Manual Download

Page: 95 / 136

Operation Manual / TPL76-C

8 Disassembly and assembly / 8.5 Removing cartridge group

HZTL2485_EN

Revision E

July 2017

* When pressing off, use diametrically opposite press-off threads. Other-
wise the bearing casing can jam and damage the turbine blades.

Check lifting gear and attach to bearing casing (42001).

Loosen nuts (61037) and remove Verbus Ripp® washers (61051).

Screw guide rod (90490) onto threaded stud (

) to balance cartridge

group.

Evenly press off cartridge group by screwing press-off screws
(90900) into the designated holes.

CAUTION

If the blades have insufficient or no clearance between the rotor and
the casing, the blades and the casing may be damaged.

Check that the blades do not rub on the turbine diffuser by rotating
the rotor.

Withdraw cartridge group.

Remove screws (42064) together with flange (42044) and also remove
possible contamination behind the flange.

Fit supports (90450) using screws (42280) and put down cartridge
group.

Cover the oil connections.

Page

133

Summary of Contents for HT576936








































































































































Search results

Summary of Contents for HT576936

Reviews:

Related manuals for HT576936

Brands by name

Popular brands

ABB HT576936, Operation Manual

Search results

Summary of Contents for HT576936

Reviews:

Related manuals for HT576936

Brands by name

Popular brands