ABB HT564904 Operation Manual Download

Page: 38 / 128

Operation Manual / TPL67-C.. - TPL71-C..

Commissioning

Inspection work

3.2

Page 36

Apr

il 2016

L2488_

ion

Inspection work

3.2

Inspection work includes preventive visual controls plus monitoring and

measuring work before and during commissioning. Inspections help detect

changes to the turbocharger. Machine damage can be avoided.

Inspection before commissioning



Check for correct functioning.



Inspect for damage.



Check oil filter for cleanliness before commissioning.

CAUTION

Contaminated oil
Particles of dirt and solid matter in the oil can cause serious damage to

the machine or property.



During initial commissioning and after all service work, the complete

lubricating system must be flushed thoroughly with warm oil.



When running in the engine and after all service work on the lubricat-

ing system, special running-in filters must be used.



Check oil pressure in oil supply lines.



Check whether the warning plates are present and legible.



Check whether the protective sheets have been removed.

3.2

3.2.1

Monitoring devices

Air filter mat

Lubricating system

Warning plates on tur-

bocharger

Summary of Contents for HT564904
































































































































Search results

Summary of Contents for HT564904

Reviews:

Related manuals for HT564904

Brands by name

Popular brands

ABB HT564904, Operation Manual

Search results

Summary of Contents for HT564904

Reviews:

Related manuals for HT564904

Brands by name

Popular brands