ABB HT564844 Operation Manual Download Page 36

Page: 36 / 128

Operation Manual / TPL67-C.. - TPL71-C..

Commissioning

Oil supply

3.1

Page 34

Apr

il 2016

L2488_

ion

Oil pressure

The oil pressure in front of the turbocharger must be maintained precisely

to ensure trouble-free operation.

The permissible oil pressure ranges at measuring point M (blind connec-

tion) on the turbocharger are listed below.

Status for operation

Oil pressure in front of the turbo-

charger [bar]

Permissible, for normal operation

1.3 … 2.5

Permissible, during engine warm-up

1.3 … 5.0

Temporarily permissible ( < 1h ) -> alarm

1.1 … 1.3

Not permissible -> emergency stop

0.0 … 1.1

Permissible, during pre- and post-lubrication

(engine stopped)

0.2 … 2.5

NOTICE

Oil orifice
To make sure these oil pressures are obtained, a regulating orifice is

fitted in the turbocharger oil inlet. The orifice is fitted by the engine

builder and secured by a safety ring.

Summary of Contents for HT564844
































































































































Search results

Summary of Contents for HT564844

Reviews:

Related manuals for HT564844

Brands by name

Popular brands

ABB HT564844, Operation Manual

Search results

Summary of Contents for HT564844

Reviews:

Related manuals for HT564844

Brands by name

Popular brands