manualshive.com logo in svg

ABB Foundation LD 810HSE Ex, Quick Installation Manual

Share
Download
ABB Foundation LD 810HSE Ex Quick Installation Manual Download Page 7

2PAA118721 

| Quick Installation Guide LD 810HSE Ex  7 

Section 2  Installation

Installation in Hazardous Locations

The LD 810HSE Ex is suitable for use and installation in areas with potentially 
explosive atmosphere in accordance to the Division model (North America) and 
the Zone model (Europe and IEC countries) of hazardous locations.

Danger of explosion!

If energized conductors are plugged to or unplugged from the 
LD 810HSE Ex in potentially explosive atmosphere, this may result 
in an explosion. Thus, do not connect or disconnect energized 
conductors!

Danger of explosion!

Do not use the LD 810HSE in hazardous areas, only the 
LD 810HSE Ex is suitable to be used in areas with potentially 
explosive atmospheres. Check the device label for device type and 
marking for explosion protection.

This manual does not supersede the applicable national regula-
tions, standards or directives. Thus, follow these regulations, 
standards or directives.

Summary of Contents for Foundation LD 810HSE Ex





































Reviews:

No comments

Brands by name

Popular brands

Load more brands