ABB DCS550 Series, Manual

Page: 249 / 316

249
Signal and parameter list
3ADW000379R0501 DCS550 Manual e e
Signal / Parameter name
m
in.
ma
x.
def
.
uni
t
63.32 FrictReleaseCmd (friction compensation, release command)
Source to release / block the friction compensation:
0 = NotUsed
constant 0; block friction compensation
1 = Auto depending on winder logic and winder macro, see WinderMacro (61.01), default
2 = Release constant 1; release friction compensation
3 = WindCtrlWord according to WindCtrlWord (61.16) bit 13
4 = DI1
1= release friction compensation; 0 = block friction compensation
5 - 23 see WriteToSpdChain (61.02)
Int. Scaling: 1 == 1
Type: C Volatile: N
No
tUs
e
d
1905B
it
3
Au
to
-
63.33 Unused
63.34 FrictionComp (friction compensation, output)
Output of the friction compensation. Calculated friction compensation torque in percent of MotNomTorque
(4.23).
Int. Scaling: 100 == 1 % Type: I
Volatile: Y
- - - %
Group 64: Write selection
Adder 1 provides two torque inputs. The sum of Add1 (64.06) can be written to other parameters by means of
Add1OutDest (64.01).
Usually adder 1 is used to write on the torque limit of the speed controller.
Commissioning hint:
−
Add1Cmd (64.04) releases Add1 (64.06). The output is forced to zero if the switch is open.
64.01 Add1OutDest (adder 1, destination of output value)
Index pointer to the sink for adder 1 output value. The format is -xxyy, with: - = negate output value, xx =
group and yy = index.
As default, nothing is connected to the output.
Int. Scaling: 1 == 1
Type: SI Volatile: N
-9999 9999 0 -
64.02 Add1In1 (adder 1, input 1)
Source (signal/parameter) for adder 1 input 1. The format is -xxyy, with: - = negate output value, xx = group
and yy = index.
Default setting of 6324 equals TensToTorq (63.24).
Int. Scaling: 1 == 1
Type: SI Volatile: N
-9999 9999 6324 -
64.03 Add1In2 (adder 1, input 2)
Source (signal/parameter) for adder 1 input 2. The format is -xxyy, with: - = negate output value, xx = group
and yy = index.
As default, nothing is connected to the input.
Int. Scaling: 1 == 1
Type: SI Volatile: N
-9999 9999 0 -
64.04 Add1ReleaseCmd (adder 1, release command)
Source to release / block adder 1:
0 = NotUsed
constant 0; block adder 1
1 = Auto depending on winder logic and winder macro, see WinderMacro (61.01), default
2 = Release constant 1; release adder 1
3 = WindCtrlWord according to WindCtrlWord (61.16) bit 14
4 = DI1
1= release adder 1; 0 = block adder 1
5 - 23 see WriteToSpdChain (61.02)
Note:
Blocking adder 1 forces its output to zero - Add1 (64.06) = 0.
Int. Scaling: 1 == 1
Type: C Volatile: N
No
tUs
e
d
1905B
it
3
Au
to
-
64.05 Unused