ABB AV1 Operating Instructions Manual Download Page 21 | Manualshive

Page: 21 / 126

background image

INTRODUCTION

SPECIFICATIONS

1 - 13

Table 1-8. Rotary Actuator Retrofit Mounting Kits

Kit Number

Drive Nomenclature

Retrofit Mounting Kit

5400309_1

UP1, UP2

Type AP positioner to
Type AV positioner

258493_1

UP3, UP4

258494_1

UP5, UP6

258527_1

AC0404

258528_1

AC0608

258529_1

AC0816

258530_2

AC1016

258527_1

AC0404

ABB part number pilot
valve positioner to Type
AV positioner

258528_1

AC0608

258529_1

AC0816

258530_1

AC1016

Table 1-9. Speed Control Orifices

1

Part Number

Size

mm

in.

5327327_1

1.02

0.04

5327327_2

Blank (drill to suit)

Blank (drill to suit)

NOTE:

1. Speed control can also be obtained by internal positioner adjustment. Refer to

PILOT VALVE

STROKE ADJUSTMENT

in Section 4.

Table 1-10. Pressure Gages

Part Number

Legend

Range

kPa

psig

5326605_4

Instrument

0 to 200

0 to 30

5326605_5

Supply

1

0 to 1,000

0 to 160

5326605_6

Output

0 to 1,000

0 to 160

NOTE:

1. The optional manifold provides gage ports, one for instrument (internal input signal), and two out-
put gages. A supply gage can be installed in the supply line (piping by customer).

Table 1-11. Supply Air Regulators with Gages

Part Number

Max. Outlet

Pressure (psig)

Max. Inlet

Pressure (psig)

Inlet/Outlet

Connections

1951029_5

125

250

¼ NPT

Table 1-12. Supply Air Filters

1

Part Number

Max. Inlet

Pressure

(psig)

Max. Temperature

Inlet/Outlet

Connection

Size

°C

°F

5328563_2

250

121.0

125.0

¼ NPT

NOTE:

1. In-line coalescing filter for removal of solid and liquid contaminants in compressed air. Filter
comes with universal mounting bracket and grade 6 filter that is 99.97% efficient at 0.3 micron. Part
number 5328563_2 has a zinc bowl.

«
...
19
20
21
22
23
...
»

Summary of Contents for AV1































































































































Reviews:

No comments

Related manuals for AV1

Brand: UEi Pages: 4

Brand: WAGER Pages: 22

LaserRange-Master T4 Pro

Brand: LaserLiner Pages: 68

DC1500 CHLORINE

Brand: LaMotte Pages: 60

Electone B-20CR

Brand: Yamaha Pages: 16

Brand: DAKOTA ULTRASONICS Pages: 38

Brand: SKF Pages: 12

Brand: Osaka Pages: 3

Brand: SIKA Pages: 8

Brand: MULTISPAN Pages: 4

Brand: Polimaster Pages: 24

LaserRange-Master T4 Pro

Brand: LaserLiner Pages: 68

UNITY INOVA NMR

Brand: Varian Pages: 65

Brand: Agilent Technologies Pages: 26

zelsius C5 -IUF

Brand: Zenner Pages: 28

Brand: R&S Pages: 46

Brand: General Pages: 16

Brand: WIKA Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands