ABB AutoLink Instruction Book Download Page 3

TEHI95094 

– Rev. 2 

 

 

 

 

 

 

 

 

         3/ 12 

 

Table of Contents 

1.

 

Introduction

 .................................................................................................................................................... 4 

2.

 

Packing and Transportation

 ........................................................................................................................ 4 

3.

 

Checking on Reception

 ............................................................................................................................... 4 

4.

 

Storage

 .......................................................................................................................................................... 5 

5.

 

Description

 .................................................................................................................................................... 5 

6.

 

Installation

 ..................................................................................................................................................... 5 

6.1

 

General

 .................................................................................................................................................. 5 

6.2

 

Installation and service conditions

 ..................................................................................................... 5 

6.3

 

Initial Setting or Previous Setting Modification Instructions

 ........................................................... 6 

6.4

 

Dip-Switch Configuration

 ..................................................................................................................... 7 

6.5

 

AutoLink Repositioning

 ........................................................................................................................ 8 

7.

 

Commissioning

 ........................................................................................................................................... 11 

7.1

 

General procedures

 ........................................................................................................................... 11 

8.

 

Maintenance

 ................................................................................................................................................ 11 

 

 

 

Summary of Contents for AutoLink













Reviews: