ABB ARG600 Single SIM Variant User Manual Download

Page: 19 / 64

LED

Label

State

Description

Led 2

LED reserved for future use

Cellular

This LED is controlled by the internal

communication module logic. For

more information, see Tools/Modem

info on the Web HMI.

Flashing

This LED is controlled by the internal

communication module logic. For

more information, see Tools/Modem

info on the Web HMI.

Off

Cellular connection is inactive

2.3

DIN rail mounting

The device has mounting holes for optional DIN rail mounting brackets. The order
code for the DIN rail mounting kit is 2RCA028234 (DIN rail clips set consisting of
a plastic clip and screws).

2.4

Product information label

The product label contains basic information about the unit such as product name,
serial number and Ethernet MAC address.

2.5

Firmware version

The device's firmware version is visible on the welcome page (

System/Welcome

Page

), which is displayed after logging in to the device.

For firmware updates, contact ABB's technical customer support.

1MRS758456 H

Section 2

ARG600 overview

ARG600 Single SIM Variant

User Manual

Summary of Contents for ARG600 Single SIM Variant































































Search results

Summary of Contents for ARG600 Single SIM Variant

Reviews:

Related manuals for ARG600 Single SIM Variant

Brands by name

Popular brands

ABB ARG600 Single SIM Variant, User Manual

Search results

Summary of Contents for ARG600 Single SIM Variant

Reviews:

Related manuals for ARG600 Single SIM Variant

Brands by name

Popular brands