manualshive.com logo in svg

ABB ACH 400, User Manual

Share
Download
ABB ACH 400 User Manual Download Page 32

Chapter 4 – Programming

4-10

ACS/ACH 400 Direct N2 Bus Interface

FL10 PANEL LOSS 

Panel loss. Panel is disconnected when Start/Stop/Dir or 
reference is coming from panel. See parameter 3002 and 
APPENDIX.
Note! If FL10 is active when the power is turned off, the 
ACS/ACH 400 will start in remote control (REM) when the 
power is turned back on.

FL11  PARAMETERING

Parameters inconsistent. Possible fault situations:
•

MINIMUM

 AI1 > 

MAXIMUM

 AI1 (parameters 1301 and 

1302)

•

MINIMUM

 AI2 > 

MAXIMUM

 AI2 (parameters 1304 and 

1305)

•

MINIMUM

 

FREQ

 > 

MAXIMUM

 

FREQ

 (parameters 2007 and 

2008)

FL12 MOTOR STALL

Motor stall. See parameter 3009 

STALL

 

FUNCTION

.

FL13 SERIAL COMM 

LOSS

Serial communication loss.

FL14 EXTERNAL 

FAULT SIGNAL

External fault is active. See parameter 3003 

EXTERNAL

 

FAULT

.

FL15 
*

OUTPUT EARTH 
FAULT

Output ground fault.

FL16 
*

DC BUS RIPPLE

DC bus ripple too high. Check power supply for phase 
loss or imbalance.

FL17 UNDERLOAD

Underload.

FL18

Reserved.

FL19 DDCS LINK

DDCS link fault.

FL20 
- 
FL28 
*

HARDWARE 
ERROR

Hardware error. Contact the factory.

“COMM LOSS” (ACS-PAN) Serial link failure. Bad connection between the control 
panel and the ACS/ACH 400.

Summary of Contents for ACH 400













































Reviews:

No comments

Brands by name

Popular brands

Load more brands