manualshive.com logo in svg

ABB A275-L59, Operation Manual, Page: 36 / 136

Share
Download
ABB A275-L59 Operation Manual Download Page 36

Operation Manual / 4 Product description / A200-L

2  Removal and installation / 2.1  Turbocharger weight

© Copyright 2018 ABB. All rights reserved.

HZTL4036_EN

Revision N

November 2018

2

Removal and installation

2.1

Turbocharger weight

Lifting gear with a sufficient load limit must be used for transporting the turbocharger. The
weight specified below applies to the heaviest variant possible. Depending on the specifica-
tion, the weight specified on the rating plate may be lower than the standard value specified
here.

Weights of the complete turbocharger

Product

Weight [kg]

A265-L

2600

A270-L

3800

A275-L

6300

A280-L

8700

Table 2: Weights A200-L with filter silencer

2.2

Removing the turbocharger

 WARNING

Risk of tipping

If the turbocharger is not sufficiently supported or not supported at all dur-
ing removal and installation, it may tip over and cause severe injury to per-
sonnel or accidents resulting in fatalities.

u

Support the turbocharger at a suitable location.

u

Secure with lifting gear wherever possible.

Wear safety helmet.

u

Loosen cable to speed sensor.

u

Disconnect all pipes according to the instructions of the enginebuilder.

u

Check lifting gear.

u

Fasten lifting gear on suspension eyes of the bearing casing and tauten.

Page 

8

 / 

108

Summary of Contents for A275-L59









































































































































Reviews:

No comments