manualshive.com logo in svg

ABB A275-L59, Operation Manual, Page: 120 / 136

Share
Download
ABB A275-L59 Operation Manual Download Page 120

Operation Manual / 4 Product description / A200-L

9  Taking a turbocharger out of operation / 9.2  Taking defective tur-
bochargers out of operation

© Copyright 2018 ABB. All rights reserved.

HZTL4036_EN

Revision N

November 2018

9.2.2

Procedure with two or more installed turbochargers per
engine

 CAUTION

Machine damage due to too high a speed

The permissible turbocharger speed for the unlocked turbocharger may not
exceed 45% of n

Bmax

. Serious damage to engine or property can be caused by

excessive speeds.

u

Observe the permissible turbocharger speed for the unlocked turbochar-
ger.

u

Reduce the engine load if necessary.

u

Stop the engine.

u

Close off oil supply to defective turbocharger.

u

Blank off the inlets and outlets of the defective turbocharger (see chapter 

Blanking off

the inlets and outlets 

→

94

).

u

Continue to operate engine in accordance with enginebuilder's instructions. Observe the
prescribed power reduction.

9.2.3

Locking the rotor

Fig. 62: Locking the rotor

Page 

92

 / 

108

Summary of Contents for A275-L59









































































































































Reviews:

No comments