ABB A175-M66 Operation Manual Download

Page: 122 / 150

Operation Manual / A170-M.. - A175-M..

10 Taking a turbocharger out of operation / 10.2 Locking the rotor

HZTL4033_EN

Rev.H

July 2021

10.2

Locking the rotor

10.2.1

Introduction

CAUTION

Cooling of a locked rotor

Serious damage to engine or property can be caused by the overheating of
intact turbocharger components.

If the gas inlet is not blanked off, the lubricating oil supply remains switched
on (see section Further information for operation of 4-stroke engines with
locked rotor).

If there is a lubricating oil leak on the turbocharger, stop the oil supply.

A locked rotor must be removed after emergency operation and checked for unbalance (see
chapter Removing the cartridge group).

The unbalance check must be carried out by an ABB Turbocharging Service Station.

Exception

The exception concerns customer requirements for test bed runs of new engines at a max-
imum engine load of up to 25 %.

In these cases, subsequent removal of the rotor is not required as the engine is only oper-
ated briefly with a locked rotor.

In these test bed runs, it is not allowed to remove any set screws from the compressor wheel
when fitting the locking device (see section

Fitting the locking device

→

121

Page

120

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operation Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands