ABB A175-M66 Operating Manual Download

Page: 148 / 150

Operation Manual / A170-M.. - A175-M..

Tables

HZTL4033_EN

Revision H

July 2021

Tables

Table 1: Definition of pictograms ............................... 9

Table 2: Personal protective equipment to be worn
at all times ...................................................................... 13

Table 3: Personal protective equipment to be worn
specific to the respective task ................................... 13

Table 4: Weight of complete turbocharger unit .... 28

Table 5: Foot screws, dimension and strength class..
34

Table 6: Foot screws, dimension CE......................... 34

Table 7: Foot screws, dimension TE ......................... 34

Table 8: Foot screws, number of cup springs ........ 34

Table 9: Torque-controlled tightening of the pres-
sure screws .................................................................... 37

Table 10: Oil pressure range........................................ 41

Table 11: Oil temperature at the inlet ....................... 42

Table 12: Oil temperature at the outlet.................... 42

Table 13: Expected replacement intervals............... 52

Table 14: Recommended replacement intervals .... 52

Table 15: Tightening torque (81272) ......................... 56

Table 16: Tightening torque (81273) ......................... 56

Table 17: Compressor cleaning parameters ........... 60

Table 18: Compressor cleaning parameters ........... 63

Table 19: Cleaning parameters Wet cleaning of tur-
bine and nozzle ring..................................................... 69

Table 20: Malfunctions when starting – Delayed
start-up .......................................................................... 70

Table 21: Malfunctions when starting – Vibrations 70

Table 22: Malfunctions when starting – Rubbing of
rotating parts................................................................ 70

Table 23: Malfunctions during operation – Lubricat-
ing oil pressure too low................................................ 71

Table 24: Malfunctions during operation – Drop in
speed ............................................................................... 71

Table 25: Malfunctions during operation – Speed in-
creases ............................................................................ 71

Table 26: Malfunctions during operation – Exhaust
gas temperature too high ........................................... 72

Table 27: Malfunctions during operation – Charge air
pressure too low ............................................................ 72

Table 28: Malfunctions during operation – Charge air
pressure too high .......................................................... 73

Table 29: Surging of the turbocharger ...................... 73

Table 30: Malfunctions when stopping – Runout
noises ............................................................................... 74

Table 31: Malfunctions when stopping – Shortened
runout time ..................................................................... 74

Table 32: Malfunction, No speed measurement sig-
nal or poor signal amplitude ....................................... 75

Table 33: Malfunction, Measured speed too high ... 75

Table 34: Malfunction, Measured speed too low .... 75

Table 35: Assembly weights ........................................ 78

Table 36: Axial clearance A ........................................... 81

Table 37: Tightening torque (56014) ......................... 95

Table 38: Tightening torque (57005) ......................... 96

Table 39: Tightening torque (61069) ......................... 98

Table 40: Tightening torque (61059 / 42128) ........ 100

Table 41: Tightening torque (86505) ....................... 101

Table 42: Inner thread size (25008).......................... 102

Table 43: Tightening torque (25013)........................ 103

Table 44: Tightening torque (61037) ....................... 104

Table 45: Tightening torque, nuts that are difficult
to access (61037) ......................................................... 104

Table 46: Tightening torque (61090)....................... 104

Table 47: Tightening torque (77015)........................ 105

Table 48: Tightening torque (72011) ........................ 107

Table 49: Axial clearance A......................................... 108

Table 50: Tightening torque (72027) ....................... 109

Table 51: Tightening torque (72027) ........................ 110

Table 52: Tightening torque (56014) ........................ 115

Table 53: Tightening torque (61009) ........................ 115

Table 54: Tightening torques..................................... 117

Table 55: Tightening torques 61009......................... 118

Table 56: Locking device tightening torque............ 121

Page

146

147

Page

146

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands