ABB A175-M66 Operating Manual Download

Page: 75 / 150

Operation Manual / A170-M.. - A175-M..

8 Troubleshooting / 8.3 Surging of the turbocharger

HZTL4033_EN

Rev.H

July 2021

Charge air pressure too high

Engine performance and engine speed unchanged, suction condition normal

Possible causes

Remedy

Turbochar-
ger

Manometer display not correct

Replace manometer

Engine

Malfunction in the injection system

Repair or contact manufacturer

Injection mistimed

Set correctly

Engine performance higher than indic-
ated

Check engine performance

Table 28: Malfunctions during operation – Charge air pressure too high

8.3

Surging of the turbocharger

CAUTION

Continuous or periodic surging

If the turbocharger surges continuously or periodically, parts of the tur-
bocharger may be damaged.

Gradually reduce the engine load.

Have the cause clarified and remedied immediately by an ABB Turbochar-
ging Service Station.

Have parts assessed for damage and, if necessary, replaced by an ABB
Turbocharging Service Station.

Surging of the turbocharger

Possible causes

Remedy

Turbocharger

Filter silencer or diffuser contamin-
ated

Heavy dirt deposits in the turbine or
in the nozzle ring

Engine

Protective grating in front of the tur-
bocharger contaminated or damaged

Clean/replace

Charge air
cooler

Cooler contaminated

Clean

Charge air duct blocked

Table 29: Surging of the turbocharger

Page

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands