ABB A175-M66 Operating Manual Download

Page: 117 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.14 Removing and installing turbine-
end nozzle ring

HZTL4033_EN

Rev.H

July 2021

Product

Size

Tightening torque [Nm]

A170-M

M10

A175-M

M10

Table 52: Tightening torque (56014)

Product

Size

Tightening torque [Nm]

Stage 1

Stage 2

Stage 3

A170-M

M18

170

280

A175-M

M20

100

240

380

Table 53: Tightening torque (61009)

1. Coat threads of new screws (56014) with high-temperature grease.

Fit the nozzle ring (56001) to the gas inlet casing (51001) using the screws (56014) and
new locking washers (56015).
Bend over locking washers.

2. Fix new spiral-wound gasket (61050) in groove of gas outlet casing (61001) at three

evenly distributed points with a little superglue (such as Loctite® 454).

3. Fit two guide studs (90321) in the upper part of the gas outlet casing (61001).

4. Coat threads of screws (61009) with high-temperature grease.

5. Loop around gas inlet casing (51001) and, using lifting gear, slide over guide studs until

at the gas outlet casing (61001) and secure with screws (61009).

6. Remove the guide studs (90321).

7. Fit remaining screws (61009), then crosswise tighten all screws (61009). Observe tight-

ening torque.

8. If present: Fit connecting pipe for turbine cleaning

Refit dismantled insulation.

Page

115

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands