ABB A175-M66 Operating Manual Download

Page: 108 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.11 Installing the compressor casing

HZTL4033_EN

Rev.H

July 2021

Turning and moving in wall insert

Fig. 62: Turning and moving in wall insert

1. Secure the lifting device (90190 / 90195) and the fixing segment (90192) to the flange of

the wall insert (77000) using the screws (90197) and washers (90198).
Carefully turn wall insert (77000) with fitted diffuser over the support angle (90025) and
pull up vertically.

2. Remove support angle (90025), screws and nuts.

3. Carefully install the wall insert (77000) in the compressor casing. Make sure both mark-

ings are in the correct position.

Page

106

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands