ABB A175-M62 Operation Manual Download

Page: 127 / 148

Operation Manual / A170-M.. - A175-M..

10 Taking a turbocharger out of operation / 10.4 Blanking off the inlets
and outlets

HZTL4033_EN

Rev.K

January 2022

Common air receiver

CAUTION

Excessive speeds on undamaged turbochargers

The speed limit n

Bmax

specified on the rating plate of the turbocharger must

not be exceeded. Serious damage to engine or property can be caused by
excessive speeds.

Observe the speeds of the undamaged turbochargers.

Reduce the engine load if necessary.

The air line must be blanked off on the engine side because the undamaged turbochargers
build up a receiver pressure.

10.4

Blanking off the inlets and outlets

The chapter is only applicable for engines with several turbochargers and joint air and ex-
haust gas receivers.

Close the lubricating oil supply to the turbocharger.

Blank off flange from compressor casing outlet, gas inlet and gas outlet by the installa-
tion of cover plates.

Observe specifications from enginebuilder.

10.5

Engines with bypass around the turbocharger

The chapter only applies for engines with one turbocharger and for systems on which the
connections for a bypass have been prepared and the necessary pipe connections have been
provided.

Close the lubricating oil supply to the turbocharger.

Open the bypass around the turbocharger.

Observe specifications from enginebuilder.

Page

125

146

Summary of Contents for A175-M62



















































































































































Search results

Summary of Contents for A175-M62

Reviews:

Related manuals for A175-M62

Brands by name

Popular brands

ABB A175-M62, Operation Manual

Search results

Summary of Contents for A175-M62

Reviews:

Related manuals for A175-M62

Brands by name

Popular brands