ABB A170-M66 Operation Manual Download

Page: 90 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.6 Removing the cartridge group

HZTL4033_EN

Rev.H

July 2021

CAUTION

Clearance between blade tip and casing

Serious damage to machinery or property can result from the rubbing or
jamming of the blade tips on the casing.

Check that the blades do not rub on the turbine diffuser during disas-
sembly/assembly by rotating the rotor.

Fig. 43: Removing cartridge group 2

Only for A170-M

1. Evenly press off cartridge group by screwing three press-off screws (90900) into the

designated holes.

2. A170-M: Using two guide studs (90490) and adapter (90199), move out the cartridge

group.
A175-M: Using two guide studs (90490), move out the cartridge group.

3. Fit supports (90450) and put down cartridge group.

4. Remove guide studs (90490). Fit and tighten the spinner nose cone (25012) together

with socket screw (25013) and washer (25014) until hand-tight.

Page

147

Summary of Contents for A170-M66





















































































































































Search results

Summary of Contents for A170-M66

Reviews:

Related manuals for A170-M66

Brands by name

Popular brands

ABB A170-M66, Operation Manual

Search results

Summary of Contents for A170-M66

Reviews:

Related manuals for A170-M66

Brands by name

Popular brands