ABB A170-M62 Operation Manual Download

Page: 115 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.14 Removing and installing turbine-
end nozzle ring

HZTL4033_EN

Rev.H

July 2021

Fig. 67: Removing the nozzle ring at the turbine end (radial gas inlet casing)

Fig. 68: Removing the nozzle ring at the turbine end (axial gas inlet casing)

1. If present: Remove connecting pipe for turbine cleaning.

2. Loop around gas inlet casing (51001) and secure with lifting gear.

3. Loosen screws (61009) and move out gas inlet casing with nozzle ring.

4. Bend open locking washers (56015), loosen and remove screws (56014).

5. Pull out nozzle ring (56001).

6. Remove spiral-wound gasket (61050) and provide new one.

Page

113

147

Summary of Contents for A170-M62





















































































































































Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands

ABB A170-M62, Operation Manual

Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands