ABB 2TMA130011A0001 Product Manual Download Page 34

Page: 34 / 38

Commissioning

Product manual 2TMD042100D0003

│

During setting, please swipe the same admin card.

Function

Action

Unlock indicator

Exit settings

Swipe admin card 1x or no
cards swiped within 15 seconds

Function

Action

Unlock indicator

Open a door

Swipe the enrolled keycard

Green

Reset to factory default

Press and hold the 1st button for
3 s to enter configuration mode.

3 LED: flash green

Press and hold the 1st button for
10 s to reset to factory default.

3 LED: OFF

Reboot the device

Door open LED: red, green,
orange cycle flash

Technical data of IC card

Work frequency

Standard

13.56 MHz

Mifare one S50/S70, Mifare desfire EV1/EV2

Note

A maximum of 64 IC cards can be supported by mini outdoor station.

2. Card management on management software

Please see the "ABB i-HD management software" product manual for more details.

Summary of Contents for 2TMA130011A0001







































Search results

Summary of Contents for 2TMA130011A0001

Reviews:

Related manuals for 2TMA130011A0001

Brands by name

Popular brands

ABB 2TMA130011A0001, Product Manual

Search results

Summary of Contents for 2TMA130011A0001

Reviews:

Related manuals for 2TMA130011A0001

Brands by name

Popular brands