ABB 2CSYD0201B Installation Manual Download Page 10

IT

 

 

 

 

10 

2CSYD0201B

 

 

 

Figure 8 

 

1) 

Set the detector sensitivity (L = low, M = medium, H = high) with the proper 
selector. 

2) 

Set the DIP switch of the detector (see the following table). 

3) 

Set the DIP switch 1 of the detector to ON (test mode). 

4) 

Lay the front cover back on the device and walk in the area to be protected 
to check if the detector signals possible intrusion attempts (the front LED 
turns on). If there are no signals, try to adjust the detection area again or to 
increase the sensitivity. Check if it works with the DomusLink3 control unit 
(please read the installation and user manuals related to the control unit for 
details about the detector test procedure). 

5) 

Remove the front cover of the detector, set the DIP switch 1 to OFF 
(standard operation), lay the cover back on the device and fix it with the 
screw. 

 

Switch 

Function 

ON 

Test mode. 

OFF * 

Standard operation. 

ON 

Suppression: only one alarm every 5 seconds is 
generated even if multiple detections occurred (the 
battery duration is reduced). 

OFF * 

Idem, but every 120 seconds. 

ON * 

N.O. Contact (do not change) 

OFF  

N.C. Contact (do not change) 

ON 

Active LED (it turns on for each detection during the 
standard operation). 

OFF * 

Inactive LED. 

ON * 

Anti-masking activated. The detector issues an hazard 
signal after having detected a masking condition for 
more than 3 minutes. 

OFF  

Antimasking deactivated. 

* Factory configuration 
 

IMPORTANT

: if the anti-masking function is activated, when you refit the front cover, 

the detector starts the self-recognition phase that lasts 1 minute. 

Summary of Contents for 2CSYD0201B

















Reviews: