manualshive.com logo in svg

AB Regin Corrigo E151-3, Manual, Page: 65 / 118

Share
Download
AB Regin Corrigo E151-3 Manual Download Page 65

Manual Corrigo Ventilation, revision R 

Chapter 12 

  Humidity control 

65  

Chapter 12  Humidity control 

Humidity control can be configured as Humidification, Dehumidification or both Humidification 
and Dehumidification.  

Two humidity sensors can be connected, a room sensor for control and an optional duct sensor for 
maximum limiting. The limit sensor can be omitted. 

The humidity control is handled by a PI-controller. 

The humidity sensors must give 0…10 V DC for 0…100 % RH. 

Humidity sensor room 

Humidity room 
Actual: 51.9% RH 
Setp: 50.0% RH 
 

Humidity sensor duct 

Humidity duct 
   Actual: 72.2% RH 
Max limit: 80.0% RH 
  Hyst.: 20.0% RH 

If the maximum limitation is 80 % RH and the hysteresis is 20 % RH, the controller output signal 
will begin decreasing at 60 % RH. When halfway to 80 % RH (i.e. when at 70 % RH), half the 
output signal will be damped. If the humidity in the duct still reaches 80 % RH, the entire output 
signal will be damped. 

 

Summary of Contents for Corrigo E151-3























































































































Reviews:

No comments