AAxeon LNP-600N User Manual Download Page 4

Page: 4 / 43

LNP600N / LNP-602N User’s Manual

Aaxeon Technologies, LLC

etting to Know Your Switch

1.1 About the LNP-600N/LNP-602N Managed Industrial

Switch

The LNP-600N/LNP-602N switch is a cost-effective and powerful industrial switch with many

features. These switches can work under wide temperature and dusty environment and

humid condition. The LNP-600N/LNP-602N support Power over Ethernet, a system to

transmit electrical power with data to remote devices over standard twisted-pair cable. The

LNP-600N/LNP-602N switch has 4 X 10/100TX PSE (Power Sourcing Equipment) ports

which are fully compliant with IEEE 802.3af standard.

1.2 Software Features



World’s fastest Redundant Ethernet Ring (Recovery time < 10ms over 250 units

connection)



Supports Ring Coupling, Dual Homing and RSTP over Redundant Ring



Support fast recovery mode



Easy web configuration

1.3 Hardware Features



Wide Operating Temperature: -40 to 75



Storage Temperature: -40 to 85



Operating Humidity: 5% to 95%, non-condensing



4 10/100Base-T(X) Ethernet port with PSE provides up to 25 watts



10/100Base-T(X) Ethernet port



100Base-FX Fiber port

Summary of Contents for LNP-600N












































Search results

Summary of Contents for LNP-600N

Reviews:

Related manuals for LNP-600N

Brands by name

Popular brands

AAxeon LNP-600N, User Manual

Search results

Summary of Contents for LNP-600N

Reviews:

Related manuals for LNP-600N

Brands by name

Popular brands