background image

3

refrigerators, mircrowave ovens, and
outer frames of heating equipment).
Take necessary precautions to avoid
electric shock. There is an increased risk
of electric shock if your body is earthed
or grounded.
6. Do not abuse the cord. Keep the cord
away from heat,oil,sharp egdes, or
moving parts. Never carry the snow
thrower by its cord or yank the cord to
disconnect it from the electrical outlet.
Damaged or entangled cords increase
the risk of electric shock.
7.Replace or properly repair damaged
cords. 
If the cord become damaged in
any manner while plugged into the wall
receptacle, immediatelly unplug the
extension cords from the receptacle.
8.Contact with water while operating
the snow thrower can result in electric
shok and serious bodily injury. 
Do not
use the snow thrower in damp or wet
locations or expose to rain.Do not
handle the plug or the appliance with
wet hands or while standing in water.
9. WARNING: Use outdoor extension
cords which are rated for outdoor use
and reduce the risk of electric shock.
10. Turn off the power switch and
disconnect the power cable before
inspecting, servicing, changing
accessories , or cleaning the snow
thrower.Follow the same procedure if
any other dangerous conditions are
present during operation
. Any
adjustments to the unit should be
performed after revolving parts inside
the snow thrower stop completely. Such
preventative safety measures reduce
the risk of starting the power tool
accidentally.

11. If you find the main power cable or
the extension cable damaged, please
pull out the plug from the socket and
disconnect the power immediately.
Repair the cable or replace it if
necessary.
12. When replacing any parts,you must
strictly observe the instructions and
procedures described in this
manual .
Special care should be paid to
any rubber parts,since these parts may
increase the engine load and decrease
its mechanical power if damaged.
13. Do not move or transport the snow
thrower when the plug is connected to
the power socket and the switch is
turned on.
14. If during use, you notice that the
unit runs unstably or hear abnormal
sounds from the engine, stop the
machine, disconnect the power
immediately and contact the service
centre.

Electrical Safety

1. Ground fault circuit interrupter (GFCI)

protection should be provided on the
circuits or outlets to be used for the
snow thrower.Receptacles are
available having built-in GFCI
protection and may be used for this
measure of safety.

2. To prevent electric shock,use only

with an extension cord suitable for
outdoor use. Before use,check that the
extension cord is in good condition.
When using an extension cord,make
sure to use one heavey enough to
carry the current your product will
draw. For lengths less than 50ft(15m),
a No.14 AWG (or greater) extension
cord should be used. An undersized

Summary of Contents for AGT3420





















Reviews: