background image

 

19

   

THE GENERATOR 

PRE-OPERATION CHECK 

NOTE:

 

Pre-operation checks should be made 

each time the generator is used. 

The engine and muffler will be very hot 

after the engine has been run. 

Avoid touching the engine and muffler 

while they are still hot with any part of 

your body or clothing during inspection or 

repair. 

WARNING:

 

If any item in the Pre-operation check is 

not working properly, have it inspected 

and repaired before operating the 

generator. 

The condition of a generator is the 

owner’s responsibility. Vital components 

can start to deteriorate quickly and 

unexpectedly, even if the generator 

unused. 

IMPORTANT

: At this point 

the user should be familiar with the 

procedures described in the section titled 

“Using the Generator for the First Time.” 

If the user has not yet read this section, go 

back and read it now. 

If this is not the first time using the 

generator, the user should take the 

following steps to prepare it for 

operation.

 

Step 1 - CHECK THE OIL 

Oil consumption is normal during 

generator use. The generator is equipped 

with a low oil pressure shutoff to protect 

it from damage. The oil level of the engine 

should be checked before each use to 

ensure that the engine crankcase contains 

sufficient lubricant. 

 

To check or add oil, follow these steps: 

1.

 

Place the generator on a level 

surface. 

2. Open access panel. Clean around oil 

fill hole. Remove dipstick and wipe the 

dipstick with a clean rag. Insert the 

dipstick into the oil fill opening 

without screwing in. Remove the 

dipstick to check the oil mark. Add 

recommended oil if the oil mark 

covers less than specified level. 

3. Slowly add more oil until the oil mark 

reaches to the top of dipstick. Do not 

over fill the crankcase. 

4. Tighten dipstick firmly, then reinstall 

small panel before starting the engine. 

5. Check generator for oil leakage. 

The point where abnormality was 

recognized by use. 

6. Check operation. If necessary, add 

recommended oil to specified level. 

7. If necessary, consult our company 

authorized dealer.

 

Step 2 - CHECK THE FUEL 
LEVEL

 

Before starting the generator, check to 

see that there is sufficient gasoline in 

the fuel tank. Add additional gasoline 

as necessary but leave sufficient room 

in tank for expansion.

 

WARNING

: This generator 

may emit highly flammable and 

explosive gasoline vapors, which can 

cause severe bums or even death if 

ignited. A nearby open flame can lead 

Summary of Contents for A112003











































Reviews: