background image

SPECIFICATIONS

9

Aavik C-280

Aavik C-580

Line:

Gain (line 1 - 4): 5-15dB; maximum input 5V RMS
Gain (line 5): 1-11dB; maximum input 8V RMS
Input impedance 10K ohm

Gain (line 1 - 4): 5-15dB; maximum input 5V RMS
Gain (line 5): 1-11dB; maximum input 8V RMS
Input impedance 10K ohm

Preamp output:

1 pair of RCA output
Max output: 8,5Vrms
Distortion, line stage: <0,005% (THD at 1kHz, 1V input)
Output impedance: 50 ohms

1 pair of RCA output
Max output: 8,5Vrms
Distortion, line stage: <0,005% (THD at 1kHz, 1V input)
Output impedance: 50 ohms

Volume control:

76 1dB steps

76 1dB steps

Aavik noise reduction:

Active Tesla Coils: 72
Active Square Tesla Coils: 156
Dither circuitry: 7

Active Tesla Coils: 108
Active Square Tesla Coils: 228
Dither circuitry: 10

Power consumption:

Standby: <1W
Operating: <12W

Standby: <1W
Operating: <12W

Dimensions:

102 x 384 x 400mm

102 x 384 x 400mm

Weight:

6,1 kg / with crossover: 6,2 kg

8,1 kg / With crossover: 8,2 kg

Active crossover
(optional module):

Crossover frequency: 60-160Hz
High pass slope: 12dB/octave
Low pass slope: 24dB/octave

Crossover frequency: 60-160Hz
High pass slope: 12dB/octave
Low pass slope: 24dB/octave

Summary of Contents for C-280











Reviews: