manualshive.com logo in svg

AAON RSMV ASM01686, Technical Manual

Share
Download
AAON RSMV ASM01686 Technical Manual Download Page 15

15

RSMV Technical Guide 

RSMV LCD SCREENS

Main Screens Map and RSMV Module Screens

RSMV Main Screens Map

Refer to the following map when navigating through the LCD Main 

Screens. To scroll through the screens, press the 

<MENU>

 button.

RSMV Module Screens

Refer to the following map when navigating through the RSMV 

Screens. From the RSMV MODULE Screen, press 

<ENTER>

 to 

scroll through the screens.

RSMV

1072vXXX

Press 

 to scroll through REFRIG MODULE Screens.

Press 

 to go to SYSTEM STATUS Screens.

SYSTEM
STATUS 

Press 

 to scroll through SYSTEM STATUS Screens.

Press 

 to go to SENSOR STATUS Screens.

SENSOR 
STATUS 

Press 

 to scroll through SENSOR STATUS Screens.

Press 

 to go to ALARMS Screens.

ALARMS

Press 

 to scroll through ALARMS Screens.

Press 

 to go to ALARM HISTORY Screens.

ALARM

HISTORY

Press 

 to scroll through ALARM HISTORY Screens.

Press 

 to go to SETPOINT STATUS Screens.

SETPOINT

STATUS

Press 

 to scroll through SETPOINT STATUS Screens.

RSMV

1072vXXX

E-BUS 

#

E-BUS COMMUNICATION DIAGNOSTICS 

Number of COMM packets received.

SOFTWARE

1072vXXX

CURRENT SOFTWARE VERSION

You can access the protected screens from this 

screen by holding the 

<UP>

 button for 5 seconds.

ADDRESS 

#

CURRENT BOARD ADDRESS

SYS TYPE 
COOLONLY

CURRENT SYSTEM TYPE

#OF COMP 

#

 

# OF COMPRESSORS

Summary of Contents for RSMV ASM01686

































Reviews:

No comments

Brands by name

Popular brands

Load more brands