AAON CB-024 Installation Operation & Maintenance Download Page 31 | Manualshive

Page: 31 / 56

AAON CB-024 Installation Operation & Maintenance Download Page 31

31

Operation

Unit  operations  should  be  controlled  with
thermostat,  or  unit  controller,  never  at  the
main  power  supply,  except  for  emergency,
servicing, or complete shutdown of the unit.

Thermostat Operation

Heating
Thermostat system switch - "Heat"
Thermostat fan switch - "Auto" or "On"
Thermostat temperature set to desired point.

Cooling
Thermostat system switch - "Cool"
Thermostat fan switch - "Auto" or "On"
Thermostat temperature set to desired point.

Air Circulation
Thermostat system switch - "Off"
Thermostat fan switch - "Auto" or "On"
No change of the thermostat temperature.
With these settings, the air handler’s supply
fan  will  run  continuously  but  the  supply  air
will not be heated, cooled, or dehumidified.

System Off
Thermostat system switch - "Off"
Thermostat fan switch - "Auto"
No change of the thermostat temperature.
With these settings, the system is shut down,
with  the  exception  of  the  control  system
power (24 VAC), and the crankcase heaters
(about 60 watts/compressor).

Night and Weekend Unoccupied Operation
To  reduce  the  operating  time  of  the  unit
when the space is unoccupied, such as nights
and  weekends,  it  is  recommended  that  the
temperature  setting  be  raised  about  5°F
while unoccupied during the cooling season
and  lowered  about  10°F  during  the  heating
season.

Compressor

The compressors must be

off

for a minimum

of 5 minutes and

on

for a minimum of 5

minutes. Short cycling of the compressors
can causes undue stress and wear.

Variable Capacity Compressor
Controller

Units with variable capacity scroll
compressors may include variable capacity
compressor controller. The following is an
explanation of the terminals and
troubleshooting of the alert flash codes on
the controller. For more information on the
compressor controller, see Emerson Climate
Bulletin AE8-1328.

COMPRESSOR CYCLING

5 MINUTE MINIMUM OFF TIME

To

prevent

motor

overheating

compressors must cycle off for a
minimum of 5 minutes.

5 MINUTE MINIMUM ON TIME

To  maintain  the  proper  oil  level
compressors  must  cycle  on  for  a
minimum of 5 minutes.

The  cycle  rate  must  not  exceed  6
starts per hour.

WARNING

«
...
29
30
31
32
33
...
»

Summary of Contents for CB-024

























































Reviews:

No comments