manualshive.com logo in svg

Aanderaa DCPS 5400, Operating Manual, Page: 64 / 150

Share
Download
Aanderaa DCPS 5400 Operating Manual Download Page 64

Page 64                                                              

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

 

 

 

If the instrument is recording, under 

Recorder Panel

, press 

“Stop All 

Groups”. 

The 

Control Panel

 is controlling the 

SeaGuardII/SmartGuard recorder and not 

individual sensors. However the Recorder 

Panel consist of three recording groups 

where you might put individual sensors in 

each group to run them on different 

recording interval. See Operation Manual 

SeaGuardII / SmartGuard for more info. 
Under each group you can start the group 

immediately by 

Start Now

, or start at a 

later time using the 

Start Delayed

 option. 

 

Figure 3-7: Recorder Panel 

 

The 

Fixed Interval

 is the recording interval for each group. The configuration of sensors in each group will influence on 

the available recording interval. If you change the configuration of one sensor and this cause a longer processing time 

the 

Fixed Interval

 might be changed.  

 

Each Sensor will do a calculation based on the configuration for each recording interval. 

 

If Acoustic Wave is enabled then the recording interval for the group containing the DCPS will be the wave 

measurement period set by 

Wave Integration Time

 in the 

System Configuration

 setting, refer chapter 

3.6.2

 and the 

current measurement period.  

 

One recording interval will then consist of a wave measurement period followed by one current measurement period. 

During the Wave measurement period only a reduced current measurement is calculated refer chapter 

3.6.8.

 Other 

sensors in the same group will present one measurement during each recording interval. 

 

 

 

 

Recording Interval 30 min 

 

 

Wave Measuring Time 20 min 

 

 

 

Current Measurement Time 10 min 

 

 

Figure 3-8: Typical Recording Interval Acoustic Wave and Current 

Summary of Contents for DCPS 5400























































































































































Reviews:

No comments