manualshive.com logo in svg

Aanderaa DCPS 5400, Operating Manual, Page: 77 / 150

Share
Download
Aanderaa DCPS 5400 Operating Manual Download Page 77

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor              

                                                     Page 77

 

 

 

3.6.1

 

Orientation 

 

 

 

 

Figure 3-28: Orientation 

 

Enable Tilt Compensation 

is recommended to set active at all time because then the sensor will automatically 

compensate for any tilt.  

Enable Fixed Heading 

might be used if there is any magnetic disturbance that might interfere with a compass heading 

and the instrument has a fix position. Then Fixed Heading (Deg.M) can be used to set the offset between the Sensor 

North direction and the Magnetic North. 

The upside down orientation setting should always be set the same way as the intended use; if the sensor is intended to 

be deployed upward looking, do not tick the 

“Enable Upside Down”

. If the sensor is intended to be deployed downward 

looking, tick the 

“Enable Upside Down”

.  

However, the sensor will work even if the orientation setting is defined as the opposite of the used direction; it is able to 

sense the orientation itself and corrects the calculated current directions, heading etc. accordingly. NB! The surface 

cell and surface reference of columns does not work if the sensor is orientated upside down while running 

(forced to be sensor referenced instead). A status flag in the record status output parameter is also set to indicate 

that the sensor has been used in the opposite direction to the configured direction. 

3.6.2

 

Wave Measurement 

 

 

 

 

 

Figure 3-29: Wave Measurement 

 

This menu is only available if Acoustic wave license is enabled. If not available ask factory for upgrade possibilities.   

 

Enable Wave Measurement

 must be selected to measure acoustic wave 

Summary of Contents for DCPS 5400























































































































































Reviews:

No comments