manualshive.com logo in svg

Aanderaa DCPS 5400, Operating Manual, Page: 82 / 150

Share
Download
Aanderaa DCPS 5400 Operating Manual Download Page 82

Page 82                                                              

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

 

 

 

3.6.7

 

Column 3 

 

 

 

 

 

 

Figure 3-35: Column 3 

 

C3 Enable Column

: Same as for C2 see chapter 

3.6.6

 

C3 Enable Surface Reference

: Same as for C1 see chapter 

3.6.5

 

C3 Cell Size

: Same as for C1 see chapter 

3.6.5

 

C3 Distance First Cell Center

: Same as for C1 see chapter 

3.6.5

 

C3 Number OF Cells

: Available from 1 to 25 cells. The instrument can measure multiple cells along the column from 

instrument to the maximum range given by the scatter condition, or from surface and down to the instrument dependent 

on the configuration. 

C3 Cell Center Spacing

: Same as for C1 see chapter 

3.6.5

  

3.6.8

 

Column 4 

 

 

 

Figure 3-36: Column 4 

 

Enable Current From Wave Pings. 

A profiler are normally not able to measure Acoustic Wave and Current 

simultaneously because the sensor using the same transducer for both operations. However with the DCPS you might 

set the 

Enable Current From Wave Ping

 which make it possible to use the data from Wave measurement pings to also 

calculate a reduced column with current. This is presented in 

Column 4

 when enabled. This column is limited to only 

measure in 3 different cells and these cells are controlled by the setting under 

User Maintenance

 and 

Wave 

Measurement,

 refer chapter 

3.7.5. 

 

Summary of Contents for DCPS 5400























































































































































Reviews:

No comments