manualshive.com logo in svg

A.R.C. Laser Nuvolas, User Manual

Share
Download
A.R.C. Laser Nuvolas User Manual Download Page 26

User Manual NUVOLAS 

April 2023

 

 

 

File: User Manual_NUVOLAS_rev3.docx

 

 

 

26 

Status LED 

The status LED indicates the state of the device. If it is blinking the device is booting. In 
case  the  LED  is  continuously  green  the  booting  process  is  finished  and  the  device  is 
ready for use. If an error occurs the System-Status-LED flashes red. 

Error LED 

The  error  LED indicates  if an error occurred. If it lights up in red, the device has to be 
restarted- 

Touchscreen 

The touchscreen the user can change parameters like power/pulse length/pulse pause 
or can change the settings of the system. 

 

 

 

A T T E N T I O N  

Since the aiming beam takes the same way through the laser transmission system as 
the  working  beam,  it  is  a  good  way  to  check  the  integrity  of  the  laser  transmission 
system. If the aiming beam does not appear at the distal end of the laser transmission 
system,  its  intensity  is  weak  or  if  it  looks  diffuse,  this  is  a  possible  indication  of  a 
damaged or malfunctioning laser transmission system. 

Never use an applicator if ist packaging is damaged, the fiber is kinked or the target 
beam is in irregular shape or not visible. 

A T T E N T I O N  

The  use  of  the  controls  or  adjustments  for  performing  procedures  other  than  those 
specified herein may result in hazardous laser radiation exposure. 

Summary of Contents for Nuvolas

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands