background image

9

Minimum clearances between the water heater and combustible 
construction are 0 inch at the sides and rear, 6” (15.2 cm) from the 
front of the jacket, and 12” (30.5 cm) from the top (standard clearance). 
If clearances stated on the heater differ from standard clearances, 
install water heater according to clearances stated on the heater.

Adequate clearance for servicing this appliance should be considered 
before installation, such as changing the anodes, etc.

A minimum clearance of 5” (12.7 cm) from the front of the jacket must 
be allowed for access to replaceable parts such as the thermostats, 
drain valve and relief valve. Provide 24” (61 cm) front clearance for 
servicing and adequate clearance between the jacket top and ceiling 
for servicing the 

fl

 ue area. 

When installing the heater, consideration must be given to proper 
location. Location selected should be as close to the wall as 
practicable and as centralized with the water piping system as 
possible.

FIGURE 4.

Never obstruct the 

fl

 ow of ventilation air.  See Figure 5.  If you have 

any doubts or questions at all, call your gas company. Failure to 
provide ventilation air can result in a 

fi

 re or explosion and can cause 

DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE.

FIGURE 5.

If this water heater will be used in beauty shops, barber shops, 
cleaning establishments, or self-service laundries with dry cleaning 
equipment, it is imperative that the water heater or water heaters 
be installed so that combustion and ventilation air be taken from 
outside these areas.  

Propellants of aerosol sprays and volatile compounds, (cleaners, 
chlorine based chemicals, refrigerants, etc.) in addition to being 
highly 

fl

 ammable in many cases, will also react to form corrosive 

hydrochloric acid when exposed to the combustion products of 
the water heater. The results can be hazardous, and also cause 
product failure.

COMBUSTION AIR AND EXHAUST TERMINATION 
CLEARANCES

Venting Through an Outside Wall - Clearances, see Figure 7.

•  0" clearance for 3" PVC, ABS, or CPVC Schedule 40 piping from 

combustible surfaces.

•  The location selection must provide clearances for servicing and 

proper operation of the water heater, see Figure 6.

FIGURE 6.

•  The venting system must be installed in a manner which allows 

inspection of the installation of the venting pipes and joints as 
well as periodic inspection after installation as required by the 
National Fuel Gas Code ANSI Z223.1.

Summary of Contents for ProMax GPDX-50





































Reviews: