background image

The company recommends professionals install the machine for you because the product 
needs to be installed and adjusted according to on-site situations of the user. 

How to install inlet metal hose and tee joint 

How to install water inlet pipe

Turn off  tap water valve and unscrew end cap of water pipe. Take tee joint out off 
accessory box and wrap its male thread with Teflon tape. Then screw the tee joint into water 
pipe. At last, wrap the male thread of end cap with Teflon tape and screw it into the other end of 
tee joint.  (see diagram 6)

Take the 1/4'' water pipe out of accessory box and cut a suitable length of water pipe. 
Connect one end of water pipe with the inlet of tee joint (refer to Diagram 6) and screw the metal 
nut to right position; connect the other end of water pipe with the inlet interface on the back of the 
machine. Please be noted that the water pipe shall be plugged in and match with the quick joint 
properly to prevent tube burst and water leakage.

Monkey wrench

Electric drill

6.2mm drill

Philips and flathead screw driver

Scissors

14-16mm wrench

19-21mm wrench

Nipple pliers

1 piece

1 piece

1 piece (drain hole)

1 piece for each

1 piece

1 piece

1 piece

1 piece

1)

2)

14

(5) ON/OFF function: Turn off " power switch" to cut off power of the whole unit.  Turn 
off " hot water switch" to stop heating function. Users can choose ON/OFF according 
to different needs. 

(6) Foot pad function: There are four foot pads at the bottom of this machine to adjust 
stability when ground is un-level.

user end of tap water

tee joint

end cap

metal nut

inlet pipe

Diagram

 6

Summary of Contents for ADR75-V-ET-1

























Reviews: